�&ǐk�@'bJ�h�ۊL'}T�:��'2�Z#$��n�a����>a��`��_3d�Qpt�/�P
-��#5�,�M���
�pA:©�q�����NW��ډ�A�����9nʺج����
�TSM��{J6?7��r�@�\����D����׶���s�f�TJj?"��D��`?��̒�	b�#�%�C*v�$�{�$����5Ծ�F�s��y�e/8��h-�f�̰
&(����Gj�L:U�	2������v�_k����Y��gp,�k�WF�R����<Q%E�,��+׬��$�䑽�0����]q�%�ˮI�����5_�}}
�c�{8�.��&���o��Ӳ�ߢ�!�2M��@��GƲz�@�Z$�b�ցK���Q��m�C���6�i����V�j|�s�y����\1�����5'?�@3�$%vP�v >��_C�R��N@���R�@�ߔ?A�w9���F("iNa-S���Q�o�3tDMLh*�#4k�T/iQ��Y*�G��m����)��8�
hBm/�I�,g�ﯖ���Z��}�Cz�q@
´��d.����L�ŕ�,��1�Z�܌�:̪���F+J-'��c�tvJ8��]Q-��b��y�6;*J`r_�d	��'�G ~p��)'�C,�%F��E(��2�k�����lР�z�!�=t��_�0��f7�
��
;�p�|�U	�%<j
��I�#!/usr/bin/bash

################################################
#
#  Spin down the given SCS disk(s).
#
#  SCSI disks (or disks that understand SCSI commands)
#  are assumed. By default, the immediate bit is set so the
#  command should return immediately. The disk however will
#  take 10 seconds or more to spin down. The '-w' option
#  causes each stop to wait until the disk reports that it
#  has stopped.
#
#  This script assumes the sg3_utils package is installed.
#
###############################################

verbose=""
immediate="-i"

usage()
{
  echo "Usage: scsi_stop [-h] [-v] [-w] <device>+"
  echo "  where:"
  echo "    -h, --help           print usage message"
  echo "    -v, --verbose        more verbose output"
  echo "    -w, --wait           wait for each stop to complete"
  echo ""
  echo "Send SCSI START STOP UNIT command to stop each <device>"
}

opt="$1"
while test ! -z "$opt" -a -z "${opt##-*}"; do
  opt=${opt#-}
  case "$opt" in
    h|-help) usage ; exit 0 ;;
    v|-verbose) verbose="-v" ;;
    w|-wait) immediate="" ;;
    *) echo "Unknown option: -$opt " ; exit 1 ;;
  esac
  shift
  opt="$1"
done

if [ $# -lt 1 ]
  then
    usage
    exit 1
fi

for i
do
# Use '-r' (read-only) otherwise using a block device node
# (e.g. 'sg_start 0 /dev/sdb') can result in a change of state
# event causing the disk to spin up again immediately.
        echo "sg_start -r $immediate 0 $verbose $i"
        sg_start -r $immediate 0 $verbose $i
done